Technology

GH-NO-LC Film: High-Transparency Dynamic Light Control

Brands building sunglasses, ski goggles and AR glasses want a lens that is bright when clear and dark when needed. Many LC lenses need polarizers, which cut light even in the clear state. Flexible GH-NO-LC film uses dichroic dyes instead, so the clear state stays bright and the tint changes with voltage.

What GH-NO-LC Film Means

The name describes how the film is built and how it behaves. Each part of it matters to a lens designer.

  • Guest Host (GH): Dichroic dye molecules, the guests, are mixed into a liquid crystal, the host.

  • Normally Open (NO): The film is clear when no voltage is applied.

  • Liquid Crystal (LC): The molecules turn when voltage is applied and the dyes turn with them.

  • Flexible: The cell is built on film, not glass, so it follows a curved lens.

In the OFF state the liquid crystal and the dye molecules line up so that light passes. When voltage is applied, the molecules turn, the dyes absorb more light and the film darkens. The tint follows the voltage, so the film can sit at any level between clear and dark. This is often called gray-scale control.

Because the dyes do the absorbing, a GH film needs no polarizer. That is the main reason it reaches a brighter clear state than polarizer-based LC. Our technology page covers SFI's GH and TN methods in more detail.

Woman wearing AR glasses, a use case for GH-NO-LC film

Planning a lens with GH-NO-LC film? Tell us about your product and target tint range and we will reply with a dedicated plan. Start your LC lens project

Why GH-NO-LC Film Gives a Brighter Clear State

A polarizer-based LC cell, such as TN, blocks about half of the light before the liquid crystal does anything. That is useful for a full blackout shutter. It is costly for eyewear that must look clear indoors. A GH film skips the polarizer, so more light reaches the eye in the clear state.

SFI GH formulations reach up to 85% transmittance in the clear state, depending on the formulation, with haze of 1% or less. The table below shows the transmittance range of the SFI formulations used in eyewear. Final values depend on each design.

Formulation

Transmittance Range (%)

LC 2

0.1–35

LC 3

17–63

LC 4

24–69

LC 5

38–78 or 50–85

How GH-NO-LC Film Behaves in a Lens

For a product team, the film's behavior comes down to a few numbers. These are the ones that shape the lens and the electronics.

  • Gray-Scale Tint: The tint follows the voltage, so the lens can hold several levels between clear and dark.

  • Fast Response: Tint changes in as little as 0.1 seconds.

  • Low Voltage: 1.8–12 VAC, depending on the product design.

  • Low Power: Under 0.1 W/ft² (1 W/m²) of film.

  • Normally Open: Clear when OFF, so a dead battery never leaves the wearer in the dark.

  • Thin and Flexible: Films start at 8 mil (0.2 mm) and follow a curved lens.

You can watch a flexible LC cell switch from clear to dark in our real sample videos.

Where GH-NO-LC Film is Used

Any eyewear that must stay bright indoors and dark in the sun is a candidate. These are the main product groups today.

  • Sunglasses: Lenses that darken on demand, even behind a car windshield, as in our adaptive sunglasses.

  • Ski Goggles: One lens for sun and flat light, as shown in our ski goggles application.

  • AR Glasses: A dimming layer that keeps the display readable outdoors, explained in what are AR glasses.

  • Helmets and Visors: Auto-dimming visors for motorcycle and sports helmets.

GH-NO-LC Film vs TN LC Film

SFI works with both GH and TN modes. The table below shows how they differ in eyewear.

Feature

GH-NO-LC

TN

Polarizer

Not required

Required

Clear-state brightness

Higher

Lower

Darkest state

Deep tint

Near blackout

Typical products

Sunglasses, goggles, AR

Strobe glasses, shutters

Brands often choose GH for everyday eyewear and TN for strobe glasses, where a full dark state matters more than clear-state brightness. Read more in why flexible LC suits strobe glasses.

Limits of GH-NO-LC Film

GH film trades some contrast for brightness. The deepest dark states, such as full blackout for strobe training, usually call for TN instead. Like any active lens, it needs a driver and a battery. The clear state is bright but never as clear as plain polycarbonate, because every layer in the lens stack absorbs some light. Each lens shape needs its own tooling and development typically takes 8–12 weeks.

Ready to design a lens with GH-NO-LC film? Send us your lens outline and tint targets and we will reply with a dedicated plan. Contact our LC team

FAQ

What Does GH-NO-LC Stand For?

Guest Host, Normally Open, Liquid Crystal. It is a flexible LC film that is clear without voltage and tints when voltage is applied.

Does GH-NO-LC Film Need a Polarizer?

No. Dichroic dyes absorb the light, so no polarizer is needed.

Is GH-NO-LC Film Clear When the Power is OFF?

Yes. It works in normally open mode, so it is clear when no voltage is applied.

Can GH-NO-LC Film Hold Partial Tint Levels?

Yes. The tint follows the voltage, so the film can hold several gray-scale levels.

How Clear is the Film in Its Clear State?

Up to 85% transmittance, depending on the formulation.

How Fast Does GH-NO-LC Film Switch?

Tint changes in as little as 0.1 seconds.

Does It Use Power to Stay Tinted?

Yes, a very small amount. The film needs voltage to hold its tint and returns to clear without it.

Which Products Use GH-NO-LC Film?

Sunglasses, ski goggles, AR glasses, helmets and visors.

Can It Be Laminated to a Curved Lens?

Yes. SFI laminates flexible LC film to polycarbonate with one or two-axis curves.